V2D.250-20D Parts
Motors, Pulleys, & Motor Specific Parts   [ Click to Browse ]
Intakes & Intake Parts   [ Click to Browse ]
Temperature Controls   [ Click to Browse ]
Gas Manifold Parts   [ Click to Browse ]
Blower
Part Per Unit List 
20MF-2-MOD 20 Inch Mixed Flow Plenum Fan for size 2 MOD. Hub specified to match motor shaft. $0.00 Order
Burner
Part Per Unit List 
HMA-2A-6-A Direct-fired burner assembly. 275,000 BTU/HR Maximum, 13,000 BTU/HR Minimum. Aluminum Casting with SS Baffles. 6" long. Used in size 1 compact & commercial direct-fired heater. Used for both Natural and Propane Gas. Pilot/Flame Rod/Spark Assembly included. $561.46 Order
  1190850
[1 used]
BURNER PART - "BRUTE" PILOT ASSEMBLY W/ SPARK & FLAME ROD. Pilot hole size is drill #50 (.070 diameter) (342B) (A0003270) Includes pack of boots and hardware. REPLACES 1190870 $176.90 Order
Replacement Parts
Part Per Unit List 
33008
[12 used]
A0003208 - 3/8" WASHERS $0.14 Order
8003
[6 used]
CONDUIT CONNECTOR - 90deg; 1/2" Bridgeport, 1/2" long thread $1.81 Order
PN10-10RX-L
[1 used]
Yellow Ring Expanded Entry for GTO Cable - Panduit Used on ignition transformers $1.97 Order
HMI_Bracket
[1 used]
20 GA. Galvanized. Used on IBT controls $2.95 Order
Controller&HMI
CAS_HMI_01_CO2
[1 used]
CAS HMI WITH CO2 SENSOR LOGO $251.00 Order
Direct Fired Air Movement Control Components
8164
[10 used]
1/4" Nylon Tubing - Used with the Modular Make-Up Air Units A1-D, A2-D, A3-D, A4-D, A5-D and the NHMUA1, NHMUA2, NHMUA3, AI (Price Per Foot). Type 12. $1.17 Order
88130
[2 used]
1/4" Plastic Union Elbow for connecting airflow tubing to airflow probes (17045 & 17045A). $5.26 Order
17045
[4 used]
Airflow Switch Components Cleveland Controls Airflow Probe 2". $7.00 Order
Direct Fired Components
MD23CABSEAL
[2 used]
A2 & A3 Direct Fired Heater Cabinent Seal. Two Required per unit. $0.91 Order
Direct Fired Flame Control Components
M4RT1
[1 used]
Fireye Flame Safety Control. Direct replacement for M series 2. Pre-purge preset 5 Sec. PTFI preset 10 Sec. Recycles once only after flame signal loss. Wiring connections are identical to M series 2. $347.50 Order
Direct Fired Sheet Metal Components
MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
D2DOORHLHL
[1 used]
DF 2 (CONTROL) DOOR LINER USED ON HINGED DOOR CONFIGURATIONS $40.15 Order
D2APPP
[2 used]
DF 2 ADJUSTING PROFILE PLATE $10.82 Order
D2BOTTH
[1 used]
DF 2 Bottom Hinged $118.83 Order
D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
D2LRDJH
[1 used]
DF 2 Left Rear Door Jamb with Viewport Hinged $23.36 Order
D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
D2DOORLH
[1 used]
DF 2 Louver Door Hinged $61.24 Order
D2PPPT
[2 used]
DF 2 PROFILE PLATE POST $6.26 Order
D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
D2RRDJH
[1 used]
DF 2 Right Rear Door Jamb Hinged $20.73 Order
D2BTPP
[1 used]
DF 2 TOP PROFILE PLATE $10.52 Order
MDBSUP
[1 used]
DF BURNER SUPPORT 22X10 GALV14GA REV0 $25.33 Order
MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
MDFRSD
[1 used]
DF FLOOR HEAT SHIELD $6.68 Order
MD15LCOVER
[1 used]
Door Louver Cover for Commercial DF 1-5 Units. $8.05 Order
MLIFTL
[4 used]
LIFTING LUG $1.88 Order
STS1643035
[6 used]
Profile Plate Spring and Hinge used on Size 2 and 3 commercial direct fired heaters. $7.00 Order
Exhaust Fan Venturi & Baffle
F5020020MUSBI
[1 used]
USBI20 - Spun Inlet. $77.52 Order
Exhaust Fan Vibration Isolators
800113-D80
[6 used]
Motor Frame Vibration Eliminator 1 3/8 Out. Dia. X 3/4" Tall, Rubber (Black with Marking) New Style, Shear 45 lbs, Compression 100 lbs. 3/8-16 x 5/8 dual studs. Durometer = 80 $2.07 Order
Exhaust Fan Wheels
F8010020P1-B-MF
[1 used]
Mixed Flow Wheel Assembly (size 20) 14 5/8" Dia. Top X 14 5/8" Dia. Ins. Bottom X 9 3/16" Height. Uses 10" Ø B Hub with P1 Bushings. *Requires P1 type split taper bushing if ordered as a replacement part. $314.59 Order
Exhaust Fan Whiz Nuts & Bolts
800043
[8 used]
A0005678 - Bolt Whiz 3/8-16 X 1 1/2, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks) $1.27 Order
11626-03224
[8 used]
Cage Nut - 1/4" - 20. Installed in 1/2" square hole. Used on 20 gauge material. $1.98 Order
5/16-18 WHIZNUT
[8 used]
Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 5/16"-18 Thread Size, 11/16" Flange Diameter, 9/32" Overall Height. $0.15 Order
Miscellaneous Electrical Parts
CAT5_3FT
[1 used]
3 Foot Long CAT5 Cable $3.53 Order
800041
[2 used]
Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks) $0.33 Order
800030
[2 used]
Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange $0.33 Order
MUA Board_DF
[1 used]
PCB for use in heaters. Used with CAS HMI. $914.18 Order
1350890
[1 used]
Terminal Assembly for Commercial DF Heaters. Terminals mounted on din rail: G,D3,D7,BO,BO,BC,BC,HB,H,H,H,F,DM,IEL,AL,N,N,NG. 285 MM DIN $108.50 Order
Miscellaneous Heater Components
NBB4000516
[6 used]
5/16" NUTS $1.01 Order
WA4000516
[10 used]
5/16" WASHERS $1.01 Order
INSULATION/sq ft
[50 used]
INSULATION (Price per Sq Foot) $3.98 Order
HG-OTA100 Assembly
[8 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
1319
[1 used]
VIEWPORT - 2" Plastic Viewport Used on the Modular Make-Up Air Units A1-D, A2-D, A3-D, A4-D, A5-D and the NHMUA1, NHMUA2, NHMUA3 Units $2.54 Order
UNI VENT II - 20"
[1 used]
Vinyl coated polyurethane foam, uv stabilized, fire retardant with continuous double glue strip. Used to seal louver cover and gaps in vbank filters, 2" wide and 1" thick. 20" Length. $3.10 Order
Miscellaneous Hood Parts
SCREW 10-24X3/8 ZINC RD HD SLOTTED MS - DOOR HANDLE
[6 used]
SCREW 10-24X3/8 ZINC RD HD SLOTTED MS - Used on UC door handles and MUA door handles $0.11 Order
104778
[1 used]
SEALANT - 10.3 oz Silicone Silver/Aluminum Sealant. 350 deg silicone used in hoods. (item #104778) $12.42 Order
Pollution Control Gasket
R-10480-S-1/4" BY 1"-15
[25 used]
Saint Gobain Gasketing-SOFT, -1/4" by 1" , Red in Color. Backing is 3 M™ Adhesive 350 acrylic ideal for very high-bond strength to many surfaces. Comes in 15' rolls. $8.93 Order
Pollution Control Hardware
90272A836
[16 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1-1/2" Length Old AX # A0026555 $0.17 Order
90272A829
[32 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
RTU Miscellaneous Components
A7-10-351-20
[8 used]
Black Compression Handle Latch and Clasp $31.07 Order
Supply Fan Miscellaneous Parts
2T4000516040000
[2 used]
5/16" BOLTS 4" LONG $1.39 Order
SB6-4-RIVET
[266 used]
RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075. $0.05 Order
ITH41234
[16 used]
SHEET METAL SCREWS 12-14 X 3/4" $0.08 Order
Supply Fan Sheet Metal Components
M2EFLS
[2 used]
2 END FLASHING $21.03 Order
B2DDC
[1 used]
AHU 2 Direct Drive Discharge Collar $12.19 Order
B2DDDDL
[1 used]
AHU 2 Direct Drive Down Discharge Liner $51.17 Order
B2ULLD
[1 used]
AHU 2 Direct Drive Lid Liner $66.54 Order
B2DDMM
[1 used]
AHU 2 Direct Drive Motor Mount $45.81 Order
B2DDMMS
[1 used]
AHU 2 Direct Drive Motor Mount Support $24.37 Order
B2DDWG
[1 used]
AHU 2 Direct Drive Wheel Guard $28.38 Order
B2LIDDPRL
[1 used]
AHU 2 LID w/Intergrated Drip Rail $99.46 Order
B2MNRL
[2 used]
AHU 2 MAIN RAIL $39.85 Order
B2RTFPH
[1 used]
AHU 2 Right Front Post Hinged $25.64 Order
B2SDBKHDD
[1 used]
AHU 2 Side Discharge Back Hinged Direct Drive $58.81 Order
B2DDBAVP
[1 used]
AHU2 Direct Drive Blower Assembly Venturi Plate $42.57 Order
MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
M2HSUP
[5 used]
HORIZONTAL SUPPORT $22.50 Order
Thermostats/Sensors
A/CP-DO-240-QC-M
[2 used]
10K, Type II thermistor with 4" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC) $45.32 Order
Transformers
1092TYPEF
[1 used]
Ignition Transformer 120V, 180VA, Output 6000 Volts Used with direct fired heaters $123.57 Order
BE161640GEK0018
[1 used]
TRANSFORMER - Low 40VA Voltage Transformer Used for 120v Primary and 24v Secondary. $16.86 Order
Curbs
Part Per Unit List 
CRB31X79X8INS ROOF CURB - 31" Wide X 79" Long X 8" High, Insulated. For the # 2 Modular Heater. $384.27 Order
CRB31X79X10INS ROOF CURB - 31" Wide X 79" Long X 10" High, Insulated. For the # 2 Modular Heater. $384.27 Order
CRB31X79X14INS ROOF CURB - 31" Wide X 79" Long X 14" High, Insulated. For the # 2 Modular Heater. $384.27 Order
CRB31X79X15INS ROOF CURB - 31" Wide X 79" Long X 15" High, Insulated. For the # 2 Modular Heater. $384.27 Order
CRB31X79X16INS ROOF CURB - 31" Wide X 79" Long X 16" High, Insulated. For the # 2 Modular Heater. $384.27 Order
CRB31X79X18INS ROOF CURB - 31" Wide X 79" Long X 18" High, Insulated. For the # 2 Modular Heater. $384.27 Order
CRB31X79X20INS ROOF CURB - 31" Wide X 79" Long X 20" High. Insulated. $392.32 Order
CRB31X79X20INS-BTC BOLT TOGETHER ROOF CURB -31" X 79" X 20" High, Insulated. 18 GA Galvanized. Ships Flat. Pitched Curb Option Not Available with Bolt Together Curbs. $222.41 Order
CRB31X79X23.5INS CURB - 31" Wide X 79" Long X 23.5" High, Insulated. For the # 2 Modular Heater. $446.46 Order
CRB31X79X24INS CURB - 31" Wide X 79" Long X 24" High, Insulated. For the # 2 Modular Heater. $446.46 Order
CRB31X79X26INS CURB - 31" Wide X 79" Long X 26" High, Insulated. For the # 2 Modular Heater. $446.46 Order
CRB31X79X28INS CURB - 31" Wide X 79" Long X 28" High, Insulated. For the # 2 Modular Heater. $446.46 Order
CRB31X79X30INS CURB - 31" Wide X 79" Long X 30" High, Insulated. For the # 2 Modular Heater. $446.46 Order
CRB31X79X36INS CURB - 31" Wide X 79" Long X 36" High, Insulated. For the # 2 Modular Heater. $534.20 Order
CRB31X79X40INS ROOF CURB - 31" Wide X 79" Long X 40" High, Insulated. For the # 2 Modular Heater. $587.63 Order
Options
Part Per Unit List 
6631T18 Combustible Gas and Carbon Monoxide Detector 120VAC input. On-Board 10A, 250V Relay and 85db Audible Alarm. 150ppm CO, 17ppm H2, 5000 ppm Methane, 35ppm Propane. (HIC-822). 10,000 cubic feet recommended coverage per detector. $1,252.93 Order
CSMDTIL Commercial Smoke Detector Interlock (Detector By Others) $7.00 Order
D4120-DST-1.5-C Duct Mounted Smoke Detector For Commercial Direct Fired Heater. Complete with detector (D4120) and sampling tube (DST-1.5). Ships Loose $589.71 Order
  D4120
[1 used]
Duct Mounted Smoke Detector For Direct Fired Heater. Air Velocity 100 to 4000 FPM, Humidity Range 0 to 95 Percentage RH, Current Consumption Alarm 125 Milliamps, Current Consumption Standby 21 Milliamps @ 24vdc, Alarm Auxiliary Contact Current @ 250 VAC 10 Amps, Alarm Auxiliary Contact Current @ 30 VDC 10 Amps, Ambient Temperature Limit -4 to 158 Degrees Fahrenheit, Photoelectric, Base. $561.26 Order
  DST-1.5
[1 used]
Duct Mounted Smoke Detector Sampling Tube, Duct Width 1 to 2 Feet, Metal, For Duct Mounted Smoke Detector, used with D4120 Detector. $25.28 Order
CABHTR100WNC Control panel enclosure heater, includes 100w, 120v heater. Recommended for winter design temperature less than 0°F. Operates on PCB controls in IBT Single Modules or RTU $410.36 Order
  D43/5200/015018
[1 used]
Enclosure heater, stainless steel sheath w/ plated fins. 100w @ 120v. 0.9 Amps. Replaces 450WSTPHTR $127.84 Order
CWCM2-1 CW Coil Module for Size 2 Modular Fans - 1,500 thru 5,300 CFM (5 Ton, 5WS0604B-37.5x36.0) Not stocked. Allow 5-6 weeks lead time. Temperature controls, mixing valves, thermostats, and freeze protection by others. $12,048.50 Order
  Condensate Drain Trap Kit
[1 used]
Condensate Drain Trap Kit - Includes PVC pipe kit used for condensate drain trap assembly. Field piping tee connection shipped loose within package. Used on all DX, CWC, MPU modules, and RTU units. $48.63 Order
  CWCM2-Shell
[1 used]
CW Coil Shell Module for Size 2 Modular Fans - 1,500 thru 5,300 CFM (5 Ton - 20 Ton CW Coil Range) Includes SS Drip Pan $1,315.05 Order
CWCM2-2 CW Coil Module for Size 2 Modular Fans - 1,500 thru 5,300 CFM (10 Ton, 5WS1004B-37.5x36.0) Not stocked. Allow 5-6 weeks lead time. Temperature controls, mixing valves, thermostats, and freeze protection by others. $12,548.50 Order
  5WS1004B 37.5 X 36.00
[0 used]
37.5 X 36.0, CW COIL, 0.625 X .02 TUBING, 0.0075 ALUMINUM FINS, GALV STEEL CASING, 2 1/2" MPT ,120.00MBH $5,376.87 Order
  Condensate Drain Trap Kit
[1 used]
Condensate Drain Trap Kit - Includes PVC pipe kit used for condensate drain trap assembly. Field piping tee connection shipped loose within package. Used on all DX, CWC, MPU modules, and RTU units. $48.63 Order
  CWCM2-Shell
[1 used]
CW Coil Shell Module for Size 2 Modular Fans - 1,500 thru 5,300 CFM (5 Ton - 20 Ton CW Coil Range) Includes SS Drip Pan $1,315.05 Order
CWCM2-3 CW Coil Module for Size 2 Modular Fans - 1,500 thru 5,300 CFM (15 Ton, 5WS1204B-37.5x36.0) Not stocked. Allow 5-6 weeks lead time. Temperature controls, mixing valves, thermostats, and freeze protection by others. $13,048.50 Order
  Condensate Drain Trap Kit
[1 used]
Condensate Drain Trap Kit - Includes PVC pipe kit used for condensate drain trap assembly. Field piping tee connection shipped loose within package. Used on all DX, CWC, MPU modules, and RTU units. $48.63 Order
  CWCM2-Shell
[1 used]
CW Coil Shell Module for Size 2 Modular Fans - 1,500 thru 5,300 CFM (5 Ton - 20 Ton CW Coil Range) Includes SS Drip Pan $1,315.05 Order
CWCM2-4 CW Coil Module for Size 2 Modular Fans - 1,500 thru 5,300 CFM (20 Ton, 5WS1404B-37.5x36.0) Not stocked. Allow 5-6 weeks lead time. Temperature controls, mixing valves, thermostats, and freeze protection by others. $13,548.50 Order
  Condensate Drain Trap Kit
[1 used]
Condensate Drain Trap Kit - Includes PVC pipe kit used for condensate drain trap assembly. Field piping tee connection shipped loose within package. Used on all DX, CWC, MPU modules, and RTU units. $48.63 Order
  CWCM2-Shell
[1 used]
CW Coil Shell Module for Size 2 Modular Fans - 1,500 thru 5,300 CFM (5 Ton - 20 Ton CW Coil Range) Includes SS Drip Pan $1,315.05 Order
NON SILICONE Fan housing assembled without the use of silicone caulk. Primarily used for paint booth applications. Use Acrylic Latex Caulk , P/N A0011848. $0.00 Order
CTR-CC DX Cooling Intake Air Thermostat and Relays Mounted in Unit - Set Point For Thermostat Should Be 85°F. $245.71 Order
  T678A1361
[1 used]
On/off stat two stage - Used with drain and fill evaporative cooler option. 20' capillary length, 55-175 degree range, 3.6 to 12 degree adjustable differential. Also used as cooling interlock thermostat. $203.13 Order
  34.110.0184.0
[2 used]
RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HC-2P-120AC-15A), with LED indicator light with AgCe contacts rated to 15A. $13.44 Order
  34.110.0147.0
[2 used]
RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4) $6.86 Order
CTR-RPI-400-CC Cooling Thermostat and Relay Mounted in Fan with 400M Series Remote Panel Interlock - Set Point For Thermostat Should Be 85°F. $245.71 Order
  T678A1361
[1 used]
On/off stat two stage - Used with drain and fill evaporative cooler option. 20' capillary length, 55-175 degree range, 3.6 to 12 degree adjustable differential. Also used as cooling interlock thermostat. $203.13 Order
  34.110.0184.0
[2 used]
RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HC-2P-120AC-15A), with LED indicator light with AgCe contacts rated to 15A. $13.44 Order
  34.110.0147.0
[2 used]
RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4) $6.86 Order
IACT-CC Intake Air Single Stage Cooling Thermostat Mounted in Unit - Set Point For Thermostat Should Be 85°F for MPU, 60°F for MPU-AC. Low Limit cooling thermostat. $205.38 Order
  T6031A1136
[1 used]
Intake Air Thermostat For Commercial Heaters - Honeywell Temp Control Used, temp range of -30 to 90 deg f and 5' capillary tube. $97.15 Order
A10DDAD3W-A 3-Way Down Discharge Air Diffuser A10, A12, A15. For Commercial Fans. $753.54 Order
  M1400M1L
[18 used]
Size 1 Industrial 3 way and 4 way diffuser blade. $4.76 Order
A10DDAD4W-A 4-Way Down Discharge Air Diffuser A10, A12, A15. For Commercial Fans. $753.54 Order
  M1400M1L
[24 used]
Size 1 Industrial 3 way and 4 way diffuser blade. $4.76 Order
A10DDAD-A 45° Down Discharge Air Diffuser A10, A12, A15. For Commercial Fans. $753.54 Order
A20SDAD-A 180° Side Discharge Air Diffuser 920. For Commercial Fans. $3,482.50 Order
FUSED_DISCONNECT_MOD FUSED DISCONNECT SWITCH FOR MODULAR UNITS $303.97 Order
CCDTP2 Downturn Plenum for Size 2 Cooling Coil Module - Required for Down Discharge Cooling Coil Applications $416.77 Order
  33008
[2 used]
A0003208 - 3/8" WASHERS $0.14 Order
  P2BACK
[1 used]
DP 2 BACK $94.91 Order
  P2BOTT
[1 used]
DP 2 BOTTOM $69.17 Order
  P2FRNT
[1 used]
DP 2 FRONT $94.91 Order
  P2LIDD
[1 used]
DP 2 LID $57.64 Order
  P2MNRL
[2 used]
DP 2 MAIN RAIL $25.13 Order
  P2SIDE
[2 used]
DP 2 SIDE $51.63 Order
  17916
[12 used]
GASKETING - Weather Stripping w/PSA , Color Gray, 1/4" X 1" (Price per foot) (17916) $1.09 Order
  INSULATION/sq ft
[39 used]
INSULATION (Price per Sq Foot) $3.98 Order
  MLIFTL
[2 used]
LIFTING LUG $1.88 Order
  SB6-4-RIVET
[50 used]
RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075. $0.05 Order
ECM Wiring Package-MUA ECM Wiring Package - DD Supply - 0-10VDC Reference Speed Control - PCB Controls (TELCO Motor) $96.52 Order
ECM Wiring Package-RTC ECM Wiring Package - DD Supply - Manual or 0-10VDC Reference Speed Control (TELCO Motor) $96.52 Order
  ECM-VCU-RTC
[1 used]
Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% speed reference with rpm indication. 24VAC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces EVO/ECM-VCU-36-MP and EVO/ECM-ACU+S1.1-MP. $103.18 Order
ECM Wiring Package - MSC ECM Wiring Package - DD Supply - Manual or 0-10VDC Reference Speed Control -MSC- (TELCO) $148.38 Order
  CAS MSC
[1 used]
Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% or 0 to 10V speed reference with rpm indication. 24VAC/24VDC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces: ECM-VCU-RTC. **Controller needs initial programming before shipping from the factory.** $150.00 Order
ECM Wiring Package-MUA ECM Wiring Package - DD Supply - Manual Reference Speed Control (TELCO Motor) - PCB Controls $96.52 Order
ECM Wiring Package-ECPM03 ECM Wiring Package - DD Supply - PWM Signal from ECPMO3 Prewire (TELCO Motor) $37.95 Order
ECRPI Evap Cooler Cooling Interlock Between Remote Panel and Heater $9.19 Order
EC-FPDK-Evap Freeze Protection Drain Control kit for Evaporative Coolers. Includes 3-Way water solenoid valve 8316G064 (shipped loose), Pressure switch installed upstream of 2way solenoid in unit, Brass Tee, 2 NPT half inch nipples, and two stage thermostat T678A1361. Field wiring required by others for 3-way valve. For both Celdek and Standard V-bank type Configurations. $798.04 Order
  A-440
[1 used]
Black Rubber Weather proof cover for Pressure switch for Evap Coolers with Freeze protection option. (Formerly EC261). $4.42 Order
  1/21THY-LFM20M34-PTI
[1 used]
Bronze Strainer. 1/2" NPT fittings on either end. 1/4" cap. 20 mesh $85.50 Order
  T6031A1136
[-1 used]
Intake Air Thermostat For Commercial Heaters - Honeywell Temp Control Used, temp range of -30 to 90 deg f and 5' capillary tube. $97.15 Order
  UD3745
[2 used]
Nipple 1/2" X close, Brass $4.53 Order
  T678A1361
[1 used]
On/off stat two stage - Used with drain and fill evaporative cooler option. 20' capillary length, 55-175 degree range, 3.6 to 12 degree adjustable differential. Also used as cooling interlock thermostat. $203.13 Order
  175097-00
[1 used]
Pressure switch for Evap Coolers with Freeze protection option. 1/4" male NPT, pressure range 1.1-3 PSI. Wired normally closed. Installed upstream of the 2 way solenoid valve in Unit. Replaces part number EC260 (174776-00). $52.35 Order
  8316G064
[1 used]
Three-Way Water Solenoid Valve. 1/2" Pipe Thread. 120V, 60Hz. Normal Closed Pressure Connection. Normally Open Exhaust Connection. $706.97 Order
IBT-EC-FPDK-Evap Freeze Protection Drain Control kit for Evaporative Coolers. Includes 3-Way water solenoid valve 8316G064 (shipped loose), Pressure switch installed upstream of 2way solenoid in unit, Brass Tee and 2 NPT half inch nipples. Field wiring required by others for 3-way valve. For both Celdek and Standard V-bank type Configurations. $798.04 Order
  A-440
[1 used]
Black Rubber Weather proof cover for Pressure switch for Evap Coolers with Freeze protection option. (Formerly EC261). $4.42 Order
  175097-00
[1 used]
Pressure switch for Evap Coolers with Freeze protection option. 1/4" male NPT, pressure range 1.1-3 PSI. Wired normally closed. Installed upstream of the 2 way solenoid valve in Unit. Replaces part number EC260 (174776-00). $52.35 Order
  8316G064
[1 used]
Three-Way Water Solenoid Valve. 1/2" Pipe Thread. 120V, 60Hz. Normal Closed Pressure Connection. Normally Open Exhaust Connection. $706.97 Order
CD-G-32x25x12 Glasdek Media for size 2 celdek evaporative cooler intake. 32in wide x 25in tall x 12in thick. $1,226.33 Order
CD-G-36x30x12 Glasdek Media for size 3 celdek evaporative cooler intake. 36in wide x 30in tall x 12in thick. $1,226.33 Order
PRESSGA15 Gas Pressure Gauge, 0-15PSI, 2.5" Diameter, 1/4" Thread Size $41.10 Order
PRESSGA35 Gas Pressure Gauge, 0-35", 2.5" Diameter, 1/4" Thread Size $41.10 Order
PRESSGA5 Gas Pressure Gauge, 0-5#, 2.5" Diameter, 1/4" Thread Size $41.10 Order
PRESSGA-5-0+15 Gas Pressure Gauge, -5 to +15 Inches Wc., 2.5" Diameter, 1/4" Thread Size $41.10 Order
143-80-2-1-G-5/8 Gas regulator - 1" diameter thread size, 10 PSI Inlet Gas Pressure. 1180 CFH, 6-14" w.c. Outlet Pressure. Includes 173-62-021-17 "Green" spring and 5/8" 10 PSI orifice. $200.21 Order
GMH-A4-4-4 High Gas Pressure Switch (1" - 20" WC) Factory set at 8" w.c. Replaces part HGP-A. $116.25 Order
LGPSO Low Pressure Gas Switch (1" - 6" WC) Factory set at 2" w.c. $168.50 Order
  GML-A4-4-4
[1 used]
LOW GAS PRESSURE SWITCH - Low Pressure Gas Switch (1" - 20" WC) Factory set at 2" w.c. Replaces part LGP-A. $116.25 Order
Gas Strainer 1" Ship Loose Gas Strainer. To be installed upstream of unit connection. 1" Connection $68.11 Order
  4417K65
[1 used]
Gas Y-Strainer, 100 Micron Mesh, 1" NPT $101.58 Order
MIAMI-DADE NOA-2 Supply Miami Dade Impact and Wind Load Certification +30 / -130 PSF - Miami Dade County Product Control Approved. Florida Building Code approval. Roof Mount Exhaust Curbs up to 20" high must be 18 gauge Aluminized. $0.00 Order
MWP-HMUA Melink Wiring Package for Heated Make-Up Air Units. 3 Phase Inverter duty Motor must be selected. $280.82 Order
  Gasket-black
[2 used]
GASKETING - Weather Stripping w/PSA , Color BLACK, 1/8" X 1" (Price per foot) $1.09 Order
  8012A
[3 used]
J-BOX - SWITCH BOX - CY X 1/2. $7.00 Order
  MRDPLATE
[1 used]
Rotary Disconnect Plate for Supply Fans. 16 GA G90 Galvanized. $8.79 Order
IBT EVAP INTERLOCK Layer Control for IBT Evap $0.00 Order
  A/CP-DO-240-QC
[1 used]
10K, Type II thermistor with 6" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC) $45.32 Order
IHC-DF2 Indoor Hanging Cradle For The Size 2 Direct Fired Unit. 2 HSA125 Hanging Isolators per Uni-Strut Included. $1,349.40 Order
  UNIVERSAL STRUT
[20 used]
1-5/8"W x 2-7/16"D 12ga Uni-strut with yellow dichromate finish for mua hanging cradle. Per foot price. $35.97 Order
  HSA125
[12 used]
Isolation spring with 125lbs resistance, 1.33" rated deflection, for hanging installation. Color, Brown $45.64 Order
AC-Interlock Cooling Interlock Relay. 24VAC Coil. 120V Contacts. Locks out burner circuit when AC is energized. $140.42 Order
  34.110.0185.0
[1 used]
RELAY - Used with part number 34.110.0147.0. (24VAC, 10 Amps) DPDT. (Clion = HHC68A-2Z-24VAC-T+LED) with LED indicator light. $13.44 Order
  34.110.0147.0
[1 used]
RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4) $6.86 Order
Burner-Interlock-IBT/RTU Burner Interlock Input. Locks out cooling when interlock is energized. $140.42 Order
Burner-Interlock Burner Interlock Relay. 120VAC Coil. 120V Contacts. Locks out burner circuit when Interlock is not energized. $140.42 Order
  34.110.0184.0
[1 used]
RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HC-2P-120AC-15A), with LED indicator light with AgCe contacts rated to 15A. $13.44 Order
  34.110.0147.0
[1 used]
RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4) $6.86 Order
CLCOMM_REV04 CASLink building monitoring system communications module. Requires internet & field wired ethernet connection or 3G cellular service. Includes Rev 3 Comm Module, RJ45 to modbus converter, 3 FT cat5 cable, and 1 FT of shielded twisted pair. $371.57 Order
  CAT5_Regular_3
[1 used]
CAT-5E CABLE - 3 Foot. $3.52 Order
  MDR-20-24
[1 used]
DIN rail power supply 100-240VAC input 24 VDC, 18 Watts Replaces: MDP18-24A-1C $41.51 Order
  88760
[1 used]
Multi-Conductor - Single Shielded Twisted Pair Cable, 18 AWG stranded (19x30) TC conductors, plenum, FEP insulation, overall shield (100% coverage), 20 AWG stranded TC drain wire, FEP jacket. Priced per foot. For use with CORE Interlock Network, light dimming 0-10VDC reference signal, and PWM signal from ECPM03 to ECM. $1.83 Order
  SCADA 2.0 CAS COM VZ
[1 used]
SCADA 2.0 CAS COM BOARD VERIZON CELLULAR KIT $653.13 Order
AC-Interlock-IBT/RTU Cooling Interlock Input to PCB Board. Locks out burner circuit when AC is energized. $140.42 Order
AUXILIARY MODBUS AUXILIARY MODBUS CONNECTION $607.93 Order
DDC-IP BACnet Monitoring Remote IP BACnet monitoring for supply fans. $1,416.51 Order
  CAS_BACNET_GATEWAY_FAN
[1 used]
BMS Gateway for BACNET MS/TP or BACNET IP. Includes CAS_GATEWAY circuit board and Protocessor BACnet interface. For use with PEM mounting standoffs. Not rated for use outside of an enclosure. When ordered as a part, specify MS/TP or IP in programmable part notes. PART REQUIRES PROGRAMMING! $1,265.11 Order
  CAT5_Regular_1
[1 used]
CAT-5E CABLE - 1.0 Foot. $4.08 Order
  RJ45_MODBUS_CONVERTER
[1 used]
RJ45 TO SHIELDED TWISTED MODBUS CONVERTER DIN RAIL MOUNTED PCB $33.56 Order
  CELLULAR VERIZON DATA- 1 YR
[1 used]
VERIZON DATA FOR 1 YEAR. FOR ONLINE STORE ORDERING ONLY. $41.25 Order
DDC-LONWorks Monitoring Remote LONWorks monitoring for supply fans. $1,416.51 Order
  FPC-N35-103-401-0862_FAN
[1 used]
Protonode Modbus to LONWORKS converter. Only to be used with fans. MUST BE PROGRAMMED (FS-QS-1211-0085 is a direct substitute) $1,277.77 Order
  RJ45_MODBUS_CONVERTER
[1 used]
RJ45 TO SHIELDED TWISTED MODBUS CONVERTER DIN RAIL MOUNTED PCB $33.56 Order
DDC-MSTP BACnet Monitoring Remote MSTP BACnet monitoring $1,416.51 Order
  CAS_BACNET_GATEWAY_FAN
[1 used]
BMS Gateway for BACNET MS/TP or BACNET IP. Includes CAS_GATEWAY circuit board and Protocessor BACnet interface. For use with PEM mounting standoffs. Not rated for use outside of an enclosure. When ordered as a part, specify MS/TP or IP in programmable part notes. PART REQUIRES PROGRAMMING! $1,265.11 Order
  CAT5_Regular_1
[1 used]
CAT-5E CABLE - 1.0 Foot. $4.08 Order
Dry Mode Dry Mode $280.90 Order
  RTUA/RH3-CP-D
[1 used]
Duct RHP Temperature and Humidity Transmitter. 3% Accuracy. $204.95 Order
  A/RH3-CP-R2-M
[1 used]
Humidity and Temperature Sensor. Wall mounted white plastic cover. For use with single gang junction box. 0-10V humidity reference, 10k thermistor. Requires 18/5 wire back to monitoring panel. $197.36 Order
  34.110.0184.0
[1 used]
RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HC-2P-120AC-15A), with LED indicator light with AgCe contacts rated to 15A. $13.44 Order
  34.110.0147.0
[1 used]
RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4) $6.86 Order
CMEXSUPV Exhaust (exhaust by others) and supply proving for commercial make up air units. Includes timed relay (88867215 timer, SS70169-D base), requires field supplied exhaust interlock. Factory set to damper opening time plus 30 seconds. $405.47 Order
  TIMER182
[1 used]
Delay on break (post purge)/delay on make electronic timer, two changeover relays rated at 2,00VA AC, 192W DC, 0.1 second to 10 minute range, 12-240V AC/DC (AC 50/60hz), green LED input indicator, red LED output indicator, DIN rail mount. $164.26 Order
  34.110.0184.0
[1 used]
RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HC-2P-120AC-15A), with LED indicator light with AgCe contacts rated to 15A. $13.44 Order
  34.110.0147.0
[1 used]
RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4) $6.86 Order
FECONTAAFS Field Wired Exhaust Contactor After Airflow Switch. Rated 23 Amps. Starts up to (2) Single Phase Motors. 2HP max. 115V, 3HP max. 240V. Starts one Three Phase Motor. 5HP max. 208V, 7.5HP 230v, 15HP max. 460V, 15HP max. 575V or (4) Dry Interlocks. Overload not Included $140.42 Order
  100-C23D10
[1 used]
Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. Used only with Rockwell 193-T1A System Overloads. $143.10 Order
FECONTBAFS Field Wired Exhaust Contactor Before Airflow Switch. Rated 23 Amps. Starts up to (2) Single Phase Motors. 2HP max. 115V, 3HP max. 240V. Starts one Three Phase Motor. 5HP max. 208V, 7.5HP max 230v, 15HP max. 460V. Overload not Included $140.42 Order
  100-C23D10
[1 used]
Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. Used only with Rockwell 193-T1A System Overloads. $143.10 Order
EXHSTARTER1-3AAFS Exhaust Fan Starter Installed in size 1, 2, or 3 heater powered after airflow swtich $210.62 Order
EXHSTARTER1-3BAFS Exhaust Fan Starter Installed in size 1, 2, or 3 heater powered before airflow switch $210.62 Order
EXHRELAYBAFS Exhaust Relay Before Airflow Switch. Provides 2 sets of NO to be used as a start command interlock for exhaust fans. $60.80 Order
  34.110.0184.0
[1 used]
RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HC-2P-120AC-15A), with LED indicator light with AgCe contacts rated to 15A. $13.44 Order
  34.110.0190.0
[2 used]
RELAY SECURITY CLIP. Used with part number 34.110.0147.0 $0.14 Order
  34.110.0147.0
[1 used]
RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4) $6.86 Order
LFS Low Fire Start. Allows the burner circuit to energize when the modulation control is in a low fire position. $0.00 Order
MANITOBA CODE No drops supplied in unit, no penetrations in base of unit. Used to meet Manitoba Canada requirement. Field wiring is made directly to disconnect switch and heater control panel terminal strip. $166.22 Order
MAN RES FSC Manual reset of flame safety controller. Used to meet Canada requirement. Flame safety will not reset on cycle of power. Dips 1,2,3,5 closed, 4, 6 open standard settings. $586.11 Order
NO CTRL DRPS No control drops supplied in unit. Field wiring is made directly to control panel. Main power drops are still supplied from disconnect. $63.26 Order
OCCUPIED SCHEDULING Occupied Scheduling Defaulted for IBT/RTU. $0.00 Order
OPPSIDE-H-CTRLS Mount motor and controls on opposite side of heater. $500.00 Order
FECONTBAFS Field Wired Exhaust Contactor Before Airflow Switch. Rated 23 Amps. Starts up to (2) Single Phase Motors. 2HP max. 115V, 3HP max. 240V. Starts one Three Phase Motor. 5HP max. 208V, 7.5HP max 230v, 15HP max. 460V. Overload not Included $140.42 Order
  100-C23D10
[1 used]
Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. Used only with Rockwell 193-T1A System Overloads. $143.10 Order
Supply Fan Preset Speed Supply Fan Preset Speed Input to PCB. Field Wired. $70.19 Order
1 Stage Cooling Terminals (Cooling by Others) 1 Stage Cooling Terminals (Cooling by Others) $53.00 Order
2 Stage Cooling Terminals (Cooling by Others) 2 Stage Cooling Terminals (Cooling by Others) $53.00 Order
6 Pole Rotary Disconnect 6 Pole 40 Amp Rotary Disconnect for Fans. Includes Switch, switch handle, mounting plate, gasket, and junction box. $199.46 Order
  Gasket-black
[2 used]
GASKETING - Weather Stripping w/PSA , Color BLACK, 1/8" X 1" (Price per foot) $1.09 Order
  8012A
[3 used]
J-BOX - SWITCH BOX - CY X 1/2. $7.00 Order
  MRDPLATE
[1 used]
Rotary Disconnect Plate for Supply Fans. 16 GA G90 Galvanized. $8.79 Order
CLOGFILTHMI Clogged Filter Switch with Notification on HMI $182.52 Order
  RFS-4100-078
[1 used]
AIR FLOW SWITCH - Used for IBT air proving switch and clogged filter switch option. Factory set @ .25", adjustable. $41.64 Order
CLOGFILT Clogged Filter Switch with Light on Remote Panel $182.52 Order
  RFS-4100-078
[1 used]
AIR FLOW SWITCH - Used for IBT air proving switch and clogged filter switch option. Factory set @ .25", adjustable. $41.64 Order
CVOUTLET GFCI 15 amp Convenience Outlet For Heater Enclosure. Power supply by others - Includes receptacle and J box. $308.88 Order
  GFR 5252
[1 used]
DCO 120/15A #1595 GFCI Receptacle $45.61 Order
  8012A
[1 used]
J-BOX - SWITCH BOX - CY X 1/2. $7.00 Order
Damper Proving Relay Damper Proving Relay $20.00 Order
  34.110.0190.0
[1 used]
RELAY SECURITY CLIP. Used with part number 34.110.0147.0 $0.14 Order
  34.110.0147.0
[1 used]
RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4) $6.86 Order
EXTENDED-DROP Extended Drop for Commercial Heaters and Supply Fans. Extends the power and remote panel connections to the unit to 20' of total length. $280.82 Order
Single Electrical Cabinet LED Lights Single Electrical Cabinet LED Lights Used on Modular MUA Units $150.32 Order
  LED Strip
[1 used]
LED Strip Light 3 feet 24V DC. $41.64 Order
  DOOR SWITCH
[1 used]
Switch, overtravel switch for door sense, single pole, double throw. Screw terminals. Vendor PNs BZ-2RQ1-A2, Z-150GQ-B $26.13 Order
  91735A146
[4 used]
Type 316 Stainless Steel Pan Head Phillips Machine Screw, 6-32 Thread, 3/8" Length. $0.41 Order
DBWSLDD-2 Double Wall Steel Liner for Direct Drive. Includes Roof, Floor, and Door Liners $491.44 Order
  D2LINA
[1 used]
Base Liner (punched part) for use with DF-2 Insulation Liner Option. $77.36 Order
LCPP-2 Profile Plate Configuration for size 2 Direct Fired Unit for low cfm applications. $6.57 Order
  D2TPPLOW
[1 used]
DF 2 TOP PROFILE PLATE. Used with 6 inch or 12 inch burner when unit operates under 2500 cfm. $3.70 Order
  SB6-4-RIVET
[4 used]
RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075. $0.05 Order
MB-AUX Mixing Box for Modular Supply Fan. Actuator Control by 2-10 VDC output. Controlled using AUX inputs $148.38 Order
SPRCM-MUA-MOD Static Pressure Mixing box Control (Mounted in Unit, preset to: -0.01 and 0.02) Used with MUA board $882.85 Order
  8164
[100 used]
1/4" Nylon Tubing - Used with the Modular Make-Up Air Units A1-D, A2-D, A3-D, A4-D, A5-D and the NHMUA1, NHMUA2, NHMUA3, AI (Price Per Foot). Type 12. $1.17 Order
  69918
[1 used]
3/16" Hose Barb , 1/8" NPT BRASS HOSE BARB FITTING $3.61 Order
  A/MLP2-D25-W-B-A-C-0P
[1 used]
ACI- MLP2 Series Low Differential Pressure transmitters, pressure range of - .25" w.c. to + .25" w.c. low temperature version. Sensor has brass fittings. Accepts 0.25 O.D. x 0.17 I.D. Push On. $177.27 Order
  AFX24SR
[1 used]
Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable. $577.19 Order
  440097-131280
[1 used]
Female 90 Degree Brass Elbow, Pipe/Thread Size 1/8" $7.70 Order
  90108A417
[2 used]
Zinc Plated Steel Type A USS WASHER, 3/8" Screw Size 1" OD, 0.06"-0.11" Thick $0.22 Order
MB2-MPU Support shell for Size 2 Modular Package Unit. Includes control vestibule. Includes condenser supports. Does not include return air or inlet air damper. $611.06 Order
  M2EFLS
[2 used]
2 END FLASHING $21.03 Order
  A7-10-351-20
[4 used]
Black Compression Handle Latch and Clasp $31.07 Order
  MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
  MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
  D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
  D2BOTTH
[1 used]
DF 2 Bottom Hinged $118.83 Order
  D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
  D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
  D2LRDJNVH
[1 used]
DF 2 Left Rear Door Jamb with No View Port Hinged $23.62 Order
  D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
  MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
  EH2RRDJH
[1 used]
EH 2 Right Rear Door Jamb Hinged $30.03 Order
  M2HSUP
[2 used]
HORIZONTAL SUPPORT $22.50 Order
  MB2DOORH
[1 used]
MB 2 Door Hinged $61.84 Order
  HG-OTA100 Assembly
[4 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
  90272A829
[24 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
MB2-MUA Mixing Box for Size 2 Modular Supply Fan. Use with MUA controls. $1,713.84 Order
  M2EFLS
[2 used]
2 END FLASHING $21.03 Order
  A7-10-351-20
[4 used]
Black Compression Handle Latch and Clasp $31.07 Order
  MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
  AFX24SR
[1 used]
Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable. $577.19 Order
  DC1209CN
[2 used]
Damper Hardware Ball Joint Used on Industrial Profile Dampers and mixing boxes. $4.99 Order
  MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
  D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
  D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
  D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
  D2LRDJNVH
[1 used]
DF 2 Left Rear Door Jamb with No View Port Hinged $23.62 Order
  D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
  MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
  EH2RRDJH
[1 used]
EH 2 Right Rear Door Jamb Hinged $30.03 Order
  M2HSUP
[2 used]
HORIZONTAL SUPPORT $22.50 Order
  MLIFTL
[0 used]
LIFTING LUG $1.88 Order
  MB2BOTTH
[1 used]
MB 2 Bottom Hinged $87.16 Order
  MB2DOORH
[1 used]
MB 2 Door Hinged $61.84 Order
  MB2CAP
[2 used]
MB 2 Mixing Box Cap 32x3.9375 $5.86 Order
  5172
[2 used]
Motorized Back Draft Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Old Vendor # SER100AC85RD. $214.96 Order
  PC12SPACER
[8 used]
PCU 1 MAIN RAIL SPACER BETWEEN MODULES 12 GA GALVANIZED $0.87 Order
  HG-OTA100 Assembly
[4 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
  9120K33
[2.5 used]
Shaft rod to connect profile dampers. 5/16" diameter, sold per foot. $5.32 Order
  1405-S
[24 used]
Short Crank Arm Used on Industrial Profile Dampers and mixing boxes. Used on 1/2 inch shaft for damper linkage. $10.00 Order
  90272A829
[24 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
MB2-IBT-MAN Mixing Box for Size 2 IBT. Actuator Control By 0-10V Output on IBT Board. $1,819.70 Order
  A/CP-DO-240-QC
[1 used]
10K, Type II thermistor with 6" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC) $45.32 Order
  M2EFLS
[2 used]
2 END FLASHING $21.03 Order
  A7-10-351-20
[4 used]
Black Compression Handle Latch and Clasp $31.07 Order
  MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
  AFX24SR
[1 used]
Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable. $577.19 Order
  DC1209CN
[2 used]
Damper Hardware Ball Joint Used on Industrial Profile Dampers and mixing boxes. $4.99 Order
  MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
  D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
  D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
  D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
  D2LRDJNVH
[1 used]
DF 2 Left Rear Door Jamb with No View Port Hinged $23.62 Order
  D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
  MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
  EH2RRDJH
[1 used]
EH 2 Right Rear Door Jamb Hinged $30.03 Order
  CP-HT-FA-12
[1 used]
High Temp 10K, Type II thermistor with average sensor wire 12' long operable up to 200F. No metal box included. $206.49 Order
  M2HSUP
[2 used]
HORIZONTAL SUPPORT $22.50 Order
  MLIFTL
[4 used]
LIFTING LUG $1.88 Order
  MB2BOTTH
[1 used]
MB 2 Bottom Hinged $87.16 Order
  MB2DOORH
[1 used]
MB 2 Door Hinged $61.84 Order
  MB2CAP
[2 used]
MB 2 Mixing Box Cap 32x3.9375 $5.86 Order
  5172
[2 used]
Motorized Back Draft Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Old Vendor # SER100AC85RD. $214.96 Order
  PC12SPACER
[8 used]
PCU 1 MAIN RAIL SPACER BETWEEN MODULES 12 GA GALVANIZED $0.87 Order
  HG-OTA100 Assembly
[4 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
  ZDB-AF2-US
[1 used]
Rotation limiter used in conjunction with AF/NF series actuators to select maximum angle of rotation. $12.00 Order
  9120K33
[2.5 used]
Shaft rod to connect profile dampers. 5/16" diameter, sold per foot. $5.32 Order
  1405-S
[2 used]
Short Crank Arm Used on Industrial Profile Dampers and mixing boxes. Used on 1/2 inch shaft for damper linkage. $10.00 Order
  90272A829
[24 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
MB2-IBT-OA Mixing Box for Size 2 IBT. Actuator Control By 0-10V Output On IBT Board to Maintain Desired Outdoor Air %. $1,819.70 Order
  A/CP-DO-240-QC
[2 used]
10K, Type II thermistor with 6" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC) $45.32 Order
  M2EFLS
[2 used]
2 END FLASHING $21.03 Order
  A7-10-351-20
[4 used]
Black Compression Handle Latch and Clasp $31.07 Order
  MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
  AFX24SR
[1 used]
Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable. $577.19 Order
  DC1209CN
[2 used]
Damper Hardware Ball Joint Used on Industrial Profile Dampers and mixing boxes. $4.99 Order
  MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
  D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
  D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
  D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
  D2LRDJNVH
[1 used]
DF 2 Left Rear Door Jamb with No View Port Hinged $23.62 Order
  D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
  MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
  EH2RRDJH
[1 used]
EH 2 Right Rear Door Jamb Hinged $30.03 Order
  CP-HT-FA-12
[1 used]
High Temp 10K, Type II thermistor with average sensor wire 12' long operable up to 200F. No metal box included. $206.49 Order
  M2HSUP
[2 used]
HORIZONTAL SUPPORT $22.50 Order
  A/RH3-CP-R2
[1 used]
Humidity and Temperature Sensor. Wall mounted white plastic cover. For use with single gang junction box. 0-10V humidity reference, 10k thermistor. Requires 18/5 wire back to monitoring panel. $197.36 Order
  MLIFTL
[4 used]
LIFTING LUG $1.88 Order
  MB2BOTTH
[1 used]
MB 2 Bottom Hinged $87.16 Order
  MB2DOORH
[1 used]
MB 2 Door Hinged $61.84 Order
  MB2CAP
[2 used]
MB 2 Mixing Box Cap 32x3.9375 $5.86 Order
  5172
[2 used]
Motorized Back Draft Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Old Vendor # SER100AC85RD. $214.96 Order
  PC12SPACER
[8 used]
PCU 1 MAIN RAIL SPACER BETWEEN MODULES 12 GA GALVANIZED $0.87 Order
  HG-OTA100 Assembly
[4 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
  ZDB-AF2-US
[1 used]
Rotation limiter used in conjunction with AF/NF series actuators to select maximum angle of rotation. $12.00 Order
  9120K33
[2.5 used]
Shaft rod to connect profile dampers. 5/16" diameter, sold per foot. $5.32 Order
  1405-S
[2 used]
Short Crank Arm Used on Industrial Profile Dampers and mixing boxes. Used on 1/2 inch shaft for damper linkage. $10.00 Order
  90272A829
[24 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
MB2-IBT-SCHEDULE Mixing Box for Size 2 IBT. Actuator Control By Schedule. $1,960.08 Order
  A/CP-DO-240-QC
[1 used]
10K, Type II thermistor with 6" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC) $45.32 Order
  M2EFLS
[2 used]
2 END FLASHING $21.03 Order
  A7-10-351-20
[4 used]
Black Compression Handle Latch and Clasp $31.07 Order
  MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
  AFX24SR
[1 used]
Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable. $577.19 Order
  DC1209CN
[2 used]
Damper Hardware Ball Joint Used on Industrial Profile Dampers and mixing boxes. $4.99 Order
  MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
  D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
  D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
  D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
  D2LRDJNVH
[1 used]
DF 2 Left Rear Door Jamb with No View Port Hinged $23.62 Order
  D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
  MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
  EH2RRDJH
[1 used]
EH 2 Right Rear Door Jamb Hinged $30.03 Order
  CP-HT-FA-12
[1 used]
High Temp 10K, Type II thermistor with average sensor wire 12' long operable up to 200F. No metal box included. $206.49 Order
  M2HSUP
[2 used]
HORIZONTAL SUPPORT $22.50 Order
  MLIFTL
[4 used]
LIFTING LUG $1.88 Order
  MB2BOTTH
[1 used]
MB 2 Bottom Hinged $87.16 Order
  MB2DOORH
[1 used]
MB 2 Door Hinged $61.84 Order
  MB2CAP
[2 used]
MB 2 Mixing Box Cap 32x3.9375 $5.86 Order
  5172
[2 used]
Motorized Back Draft Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Old Vendor # SER100AC85RD. $214.96 Order
  PC12SPACER
[8 used]
PCU 1 MAIN RAIL SPACER BETWEEN MODULES 12 GA GALVANIZED $0.87 Order
  HG-OTA100 Assembly
[4 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
  ZDB-AF2-US
[1 used]
Rotation limiter used in conjunction with AF/NF series actuators to select maximum angle of rotation. $12.00 Order
  9120K33
[2.5 used]
Shaft rod to connect profile dampers. 5/16" diameter, sold per foot. $5.32 Order
  1405-S
[24 used]
Short Crank Arm Used on Industrial Profile Dampers and mixing boxes. Used on 1/2 inch shaft for damper linkage. $10.00 Order
  90272A829
[24 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
MB2-BAS Mixing Box for Size 2 Modular Supply Fan. Actuator Control by 2-10 VDC input. $1,623.10 Order
  M2EFLS
[2 used]
2 END FLASHING $21.03 Order
  A7-10-351-20
[4 used]
Black Compression Handle Latch and Clasp $31.07 Order
  MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
  AFX24SR
[1 used]
Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable. $577.19 Order
  DC1209CN
[2 used]
Damper Hardware Ball Joint Used on Industrial Profile Dampers and mixing boxes. $4.99 Order
  MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
  D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
  D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
  D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
  D2LRDJNVH
[1 used]
DF 2 Left Rear Door Jamb with No View Port Hinged $23.62 Order
  D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
  MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
  EH2RRDJH
[1 used]
EH 2 Right Rear Door Jamb Hinged $30.03 Order
  M2HSUP
[2 used]
HORIZONTAL SUPPORT $22.50 Order
  MLIFTL
[4 used]
LIFTING LUG $1.88 Order
  MB2BOTTH
[1 used]
MB 2 Bottom Hinged $87.16 Order
  MB2DOORH
[1 used]
MB 2 Door Hinged $61.84 Order
  MB2CAP
[2 used]
MB 2 Mixing Box Cap 32x3.9375 $5.86 Order
  5172
[2 used]
Motorized Back Draft Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Old Vendor # SER100AC85RD. $214.96 Order
  PC12SPACER
[8 used]
PCU 1 MAIN RAIL SPACER BETWEEN MODULES 12 GA GALVANIZED $0.87 Order
  HG-OTA100 Assembly
[4 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
  ZDB-AF2-US
[1 used]
Rotation limiter used in conjunction with AF/NF series actuators to select maximum angle of rotation. $12.00 Order
  9120K33
[2.5 used]
Shaft rod to connect profile dampers. 5/16" diameter, sold per foot. $5.32 Order
  1405-S
[2 used]
Short Crank Arm Used on Industrial Profile Dampers and mixing boxes. Used on 1/2 inch shaft for damper linkage. $10.00 Order
  90272A829
[24 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
MB2-SP Mixing Box for Size 2 Modular Supply Fan. Actuator Control by Static Pressure. Photohelic included. $2,466.56 Order
  M2EFLS
[2 used]
2 END FLASHING $21.03 Order
  AMB24-3
[1 used]
Actuator used for floating point operation, 24vac power, 2.5 watts, 180 in-lb torque, 95 second opening time, 3ft connection cable, 1/2" conduit connections. $337.02 Order
  A7-10-351-20
[4 used]
Black Compression Handle Latch and Clasp $31.07 Order
  MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
  DC1209CN
[2 used]
Damper Hardware Ball Joint Used on Industrial Profile Dampers and mixing boxes. $4.99 Order
  MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
  D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
  D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
  D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
  D2LRDJNVH
[1 used]
DF 2 Left Rear Door Jamb with No View Port Hinged $23.62 Order
  D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
  MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
  EH2RRDJH
[1 used]
EH 2 Right Rear Door Jamb Hinged $30.03 Order
  M2HSUP
[2 used]
HORIZONTAL SUPPORT $22.50 Order
  MLIFTL
[4 used]
LIFTING LUG $1.88 Order
  MB2BOTTH
[1 used]
MB 2 Bottom Hinged $87.16 Order
  MB2DOORH
[1 used]
MB 2 Door Hinged $61.84 Order
  MB2CAP
[2 used]
MB 2 Mixing Box Cap 32x3.9375 $5.86 Order
  5172
[2 used]
Motorized Back Draft Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Old Vendor # SER100AC85RD. $214.96 Order
  PC12SPACER
[8 used]
PCU 1 MAIN RAIL SPACER BETWEEN MODULES 12 GA GALVANIZED $0.87 Order
  A3300-0-LT
[1 used]
Photohelic pressure differential guage (gauge only, accessories listed below), dual relay, pressure range of -.25" w.c. to .25" w.c. low temperature version, standard 80/20 guage. "RPPHOTOHELIC" includes remote mounting box. "A-306" contains pressure kit. $1,182.75 Order
  HG-OTA100 Assembly
[4 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
  9120K33
[2.5 used]
Shaft rod to connect profile dampers. 5/16" diameter, sold per foot. $5.32 Order
  1405-S
[24 used]
Short Crank Arm Used on Industrial Profile Dampers and mixing boxes. Used on 1/2 inch shaft for damper linkage. $10.00 Order
  A-306
[1 used]
Static Pressure Kit for Photohelic, contains 1/8" id tubing, fittings and outdoor sensor. $136.43 Order
  90272A829
[24 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
MB2-MP Mixing Box for Size 2 Modular Supply Fan. Actuator Control by Manual Potentiometer. Manual Potenentiometer included. $2,281.20 Order
  M2EFLS
[2 used]
2 END FLASHING $21.03 Order
  A7-10-351-20
[4 used]
Black Compression Handle Latch and Clasp $31.07 Order
  MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
  AFB24-MFT95
[1 used]
Damper Actuator, AF Series (DCA) Spring Return (< 60sec), 180 in-lb torque. Running time 150 seconds, 7.5 watts, adjustable end stop 35-90 degrees, angle rotation 95 degrees, up to 1.05" shaft. Controlled via 135 ohm Potentiometer. $589.71 Order
  DC1209CN
[2 used]
Damper Hardware Ball Joint Used on Industrial Profile Dampers and mixing boxes. $4.99 Order
  MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
  D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
  D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
  D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
  D2LRDJNVH
[1 used]
DF 2 Left Rear Door Jamb with No View Port Hinged $23.62 Order
  D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
  MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
  EH2RRDJH
[1 used]
EH 2 Right Rear Door Jamb Hinged $30.03 Order
  M2HSUP
[2 used]
HORIZONTAL SUPPORT $22.50 Order
  MLIFTL
[4 used]
LIFTING LUG $1.88 Order
  S963B1128
[1 used]
Manual potentiometer 135ohm $115.76 Order
  MB2BOTTH
[1 used]
MB 2 Bottom Hinged $87.16 Order
  MB2DOORH
[1 used]
MB 2 Door Hinged $61.84 Order
  MB2CAP
[1 used]
MB 2 Mixing Box Cap 32x3.9375 $5.86 Order
  5172
[2 used]
Motorized Back Draft Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Old Vendor # SER100AC85RD. $214.96 Order
  PC12SPACER
[8 used]
PCU 1 MAIN RAIL SPACER BETWEEN MODULES 12 GA GALVANIZED $0.87 Order
  HG-OTA100 Assembly
[4 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
  ZDB-AF2-US
[24 used]
Rotation limiter used in conjunction with AF/NF series actuators to select maximum angle of rotation. $12.00 Order
  9120K33
[2.5 used]
Shaft rod to connect profile dampers. 5/16" diameter, sold per foot. $5.32 Order
  1405-S
[2 used]
Short Crank Arm Used on Industrial Profile Dampers and mixing boxes. Used on 1/2 inch shaft for damper linkage. $10.00 Order
  90272A829
[24 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
MB2-TP Mixing Box for Size 2 Modular Supply Fan. 2-Position Actuator Control. Interlock field wired by others. Spring Return to Outside Air Position. $1,520.41 Order
  M2EFLS
[2 used]
2 END FLASHING $21.03 Order
  A7-10-351-20
[4 used]
Black Compression Handle Latch and Clasp $31.07 Order
  MCONWAS
[4 used]
Connecting Washer 12 Gauge 2-7/8" x 2-7/8" $2.29 Order
  AFX24SR
[1 used]
Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable. $577.19 Order
  DC1209CN
[2 used]
Damper Hardware Ball Joint Used on Industrial Profile Dampers and mixing boxes. $4.99 Order
  MD12MR
[2 used]
DF 1-2 MAIN RAIL 45.25X8 GALV14GA REV5 $41.72 Order
  D13TDSPDPRL
[2 used]
DF 1-3 Top Door Support w/Integrated Drip Rail $41.03 Order
  D2DOORH
[1 used]
DF 2 Burner Hinged Door $61.88 Order
  D2LTFPH
[1 used]
DF 2 Left Front Post Hinged $23.62 Order
  D2LRDJNVH
[1 used]
DF 2 Left Rear Door Jamb with No View Port Hinged $23.62 Order
  D2LIDDPRL
[1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  D2RTFPH
[1 used]
DF 2 Right Front Post Hinged $29.99 Order
  MDEBRD
[1 used]
DF ELECTRIC BOARD $36.40 Order
  EH2RRDJH
[1 used]
EH 2 Right Rear Door Jamb Hinged $30.03 Order
  M2HSUP
[2 used]
HORIZONTAL SUPPORT $22.50 Order
  MLIFTL
[4 used]
LIFTING LUG $1.88 Order
  MB2BOTTH
[1 used]
MB 2 Bottom Hinged $87.16 Order
  MB2DOORH
[1 used]
MB 2 Door Hinged $61.84 Order
  MB2CAP
[2 used]
MB 2 Mixing Box Cap 32x3.9375 $5.86 Order
  5172
[2 used]
Motorized Back Draft Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Old Vendor # SER100AC85RD. $214.96 Order
  PC12SPACER
[8 used]
PCU 1 MAIN RAIL SPACER BETWEEN MODULES 12 GA GALVANIZED $0.87 Order
  HG-OTA100 Assembly
[4 used]
Removable Door Hinge Assembly used on Pollution Control Units and KB Blowers. Includes male and female quick release pieces. $12.97 Order
  9120K33
[2.5 used]
Shaft rod to connect profile dampers. 5/16" diameter, sold per foot. $5.32 Order
  1405-S
[2 used]
Short Crank Arm Used on Industrial Profile Dampers and mixing boxes. Used on 1/2 inch shaft for damper linkage. $10.00 Order
  90272A829
[24 used]
Zinc-Plated Steel Pan Head Phillips Machine Screw, 10-32 Thread, 1/2" Length $0.17 Order
A2UPDISCH-DD Up Discharge Construction for Direct Drive AHUs $1,160.30 Order
  B2ULLD
[-1 used]
AHU 2 Direct Drive Lid Liner $66.54 Order
  B2DDBKH
[1 used]
AHU 2 Down Discharge Back Hinged $82.32 Order
  B2LIDDPRLUP
[1 used]
AHU 2 LID Up Discharge w/Intergrated Drip Rail $99.46 Order
  B2LIDDPRL
[-1 used]
AHU 2 LID w/Intergrated Drip Rail $99.46 Order
  B2SDBKHDD
[-1 used]
AHU 2 Side Discharge Back Hinged Direct Drive $58.81 Order
Shaft Grounding Ring Option Shaft Grounding Ring Option $0.00 Order
A2-D-MBDD INS Motorized Back Draft Insulated Damper 22.75" X 24" for Size 2 Standard & Modular Heater Units w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, Low Leakage, LF120S Actuator Included. Insulated blades and frame. Thermally broken blades. $1,354.89 Order
  LF120-S
[1 used]
ACTUATOR- LF Series, (DCA) Spring Return, 35 in-lb torqe. Fits 3/8" - 1/2" shaft, Control direction CW & CCW, Spring direction reversible; 1/2" conduit fittings. $326.43 Order
  5172-INS
[1 used]
Motorized Back Draft Insulated Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Insulated blades and frame. Thermally broken blades. $762.38 Order
A2-D-MBDD-SL Direct Fired -- Motorized Back Draft Discharge Damper Shipped Loose 30" X 30" for Size 2 Units w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, Low Leakage, NFBUP-S Actuator Included, Field Installation Required. Damper, actuator & actuator cover (p/n ACTCOVERMOD) factory assembled. $1,082.74 Order
  NFBUP-S
[1 used]
ACTUATOR - NF Series (DCA) Spring Return, 90 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 24-240vac, 24-125vdc, 6.5VA @ 120vac, 95° Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for NF120-S. $377.61 Order
  ACTCOVERMOD
[1 used]
ACTUATOR COVER - Used on shipped loose discharge damper optionto protect damper actuators. Used on enginia dampers. $5.95 Order
  5173
[1 used]
Motorized Back Draft Damper 30" X 30" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, NFBUP-S Actuator Not Included, for Size 3 Heater and Untempered Housing. Old Vendor # SER100AC86RD. $276.36 Order
FIELDDMP(S) Field Supplied Damper(s) Indicated By Others $0.00 Order
A2-D-MBDD Motorized Back Draft Damper 22.75" X 24" for Size 2 Standard & Modular Heater Units w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, Low Leakage, LF120S Actuator Included $541.36 Order
  LF120-S
[1 used]
ACTUATOR- LF Series, (DCA) Spring Return, 35 in-lb torqe. Fits 3/8" - 1/2" shaft, Control direction CW & CCW, Spring direction reversible; 1/2" conduit fittings. $326.43 Order
  5172
[1 used]
Motorized Back Draft Damper 22.75" X 24" w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, LF120S Actuator Not Included, for Size 2 Heater and Untempered Housing. Old Vendor # SER100AC85RD. $214.96 Order
Full Crating for Heater Full crating for commercial heaters for shipping. $430.25 Order
ENAM-1 Tan Enamel Coating (exterior walls/roof) For Heaters with 7"-15" blower wheels, includes casing and intakes. Consult factory for other colors. Sherwin Williams p/n F75KXN5809-4347, (AX = A0006229) $7,305.61 Order
Condenser_Locking_Caps_2 Locking caps for double condenser units. Consists of 4 locking caps, part# NCP-4, and 1 key, part# NC-KEY. $130.59 Order
  NC-KEYJB
[1 used]
NONVENT Cap key. Works with NONVENT Caps and is required to remove them. Required to unlock 86682 (old# NCP-4) locking condensing unit caps. $44.59 Order
Condenser_Locking_Caps_1 Locking caps for single condenser units. Consists of 2 locking caps, part# NCP-4, and 1 key, part# NC-KEY. $85.37 Order
  NC-KEYJB
[1 used]
NONVENT Cap key. Works with NONVENT Caps and is required to remove them. Required to unlock 86682 (old# NCP-4) locking condensing unit caps. $44.59 Order
SP-MPU-1C Single Point MPU Connection, 1 Condenser. $638.87 Order
  193-T1APM
[1 used]
Rockwell Overload DIN Rail/Panel Mounting Adapter for 193-T series overload. $12.06 Order
  UDJ-160A
[3 used]
Single Pole, 160A, 600V max distribution block. DIN rail mountable. 1 input 8-3/0 AWG wire size, 7 outputs 14-4 AWG wire size. $34.83 Order
SP-MPU-2C Single Point MPU Connection, 2 Condensers. $1,277.77 Order
  193-T1APM
[2 used]
Rockwell Overload DIN Rail/Panel Mounting Adapter for 193-T series overload. $12.06 Order
  UDJ-160A
[3 used]
Single Pole, 160A, 600V max distribution block. DIN rail mountable. 1 input 8-3/0 AWG wire size, 7 outputs 14-4 AWG wire size. $34.83 Order
MELIM-2 Size 2 Moisture Eliminator Option for DX Coil, MPUs and Chilled Water Coils - allows cooling coil face velocity to increase to 650 fpm. Increases cooling coil max cfm to 6000 cfm. $990.90 Order
  MES37X37X1
[1 used]
37" H x 37" H moisture eliminator panel used in size 2 cooling coil moisture eliminator options. $1,155.01 Order
  MCC2MEBK
[2 used]
SIZE 2 Moisture Eliminator Bracket $22.83 Order
MELIM-2-AC Size 2 MPU-AC Moisture Eliminator Option - allows cooling coil face velocity to increase to 650 fpm. Increases cooling coil max cfm to 3250 cfm. $577.20 Order
  MES21X37X1
[1 used]
21" H x 37" L moisture eliminator panel used in size 2 MPU-AC moisture eliminator options. $655.83 Order
  MCC2MEBK
[2 used]
SIZE 2 Moisture Eliminator Bracket $22.83 Order
D-Hanger Curb Duct Hanger - 1-1/4" Angle Iron Frame Welded to Curb to support standard size ductwork. Priced per curb. Only available when curb assembly is ordered. $140.42 Order
MB2-MERV 13-EXTRA Extra set of MERV 13 filters for Size 2 Mixing Box. Uses 2 20 x 25 x 2 inch filters and 1 16 x 25 x 2 inch filters. $132.98 Order
  DP13-STD2-202
[1 used]
Throw away filter 16w x 25h x 2d, MERV13 rating, 1400 max cfm. $19.23 Order
  DP13-STD2-204
[2 used]
Throw away filter 20w x 25h x 2d, MERV13 rating, 1750 max cfm. 12 per box $22.71 Order
MB2-MERV 8-EXTRA Extra set of MERV 8 filters for Size 2 Mixing Box. Uses 2 20 x 25 x 2 inch filters and 1 16 x 25 x 2 inch filters. $37.95 Order
  TA 16X25X2
[1 used]
Filter throw away filter 16" x 25" x 2". MERV 8. (DP40) $11.61 Order
  TA 20X25X2
[2 used]
Filter throw away filter 20" x 25" x 2". MERV 8. (DP40), 12 per box $8.65 Order
MB2-MERV 13 MERV 13 filter option for Size 2 Mixing Box or Condenser Support. Mixing Box or Condenser Support must be selected for this option. Uses 2 20 x 25 x 2 inch filters and 1 16 x 25 x 2 inch filters. $227.72 Order
  17916
[11 used]
GASKETING - Weather Stripping w/PSA , Color Gray, 1/4" X 1" (Price per foot) (17916) $1.09 Order
  A-17
[2 used]
Ludwig A-17 Clip (Hood Retaining) 1" Width X 2 1/2" Height, Spring Steel - Exh.fans, Includes Mounting Hardware When Shipped As A Replacement Part. Old AX# A0005723. $1.30 Order
  MB2CSBR
[4 used]
MB 2 CROSS BRACE 28.816" X 2.958" 20 GA GALV $0.56 Order
  MB2DSRL
[1 used]
MB 2 DOOR SIDE RAIL 39.00" X 6.77" 20 GA GALV $1.52 Order
  MB2FTRL
[1 used]
MB 2 FILTER RAIL 39.00" X 6.77" 20 GA GALV $1.72 Order
  MB2FTSP
[1 used]
MB 2 FILTER STOP 15.00" X 3.837" 20 GA GALV $0.40 Order
  MB2LTFPH
[1 used]
MB 2 Left Front Post Hinged $13.35 Order
  MB2LRDJH
[1 used]
MB 2 Left Rear Door Jamb Hinged $23.42 Order
  SB6-4-RIVET
[15 used]
RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075. $0.05 Order
  DP13-STD2-202
[1 used]
Throw away filter 16w x 25h x 2d, MERV13 rating, 1400 max cfm. $19.23 Order
  DP13-STD2-204
[2 used]
Throw away filter 20w x 25h x 2d, MERV13 rating, 1750 max cfm. 12 per box $22.71 Order
MB2-MERV 8 MERV 8 filter option for Size 2 Mixing Box or Condenser Support. Mixing Box or Condenser Support must be selected for this option. Uses 2 20 x 25 x 2 inch filters and 1 16 x 25 x 2 inch filters. $151.82 Order
  TA 16X25X2
[1 used]
Filter throw away filter 16" x 25" x 2". MERV 8. (DP40) $11.61 Order
  TA 20X25X2
[2 used]
Filter throw away filter 20" x 25" x 2". MERV 8. (DP40), 12 per box $8.65 Order
  17916
[11 used]
GASKETING - Weather Stripping w/PSA , Color Gray, 1/4" X 1" (Price per foot) (17916) $1.09 Order
  A-17
[2 used]
Ludwig A-17 Clip (Hood Retaining) 1" Width X 2 1/2" Height, Spring Steel - Exh.fans, Includes Mounting Hardware When Shipped As A Replacement Part. Old AX# A0005723. $1.30 Order
  MB2CSBR
[4 used]
MB 2 CROSS BRACE 28.816" X 2.958" 20 GA GALV $0.56 Order
  MB2DSRL
[1 used]
MB 2 DOOR SIDE RAIL 39.00" X 6.77" 20 GA GALV $1.52 Order
  MB2FTRL
[1 used]
MB 2 FILTER RAIL 39.00" X 6.77" 20 GA GALV $1.72 Order
  MB2FTSP
[1 used]
MB 2 FILTER STOP 15.00" X 3.837" 20 GA GALV $0.40 Order
  MB2LTFPH
[1 used]
MB 2 Left Front Post Hinged $13.35 Order
  MB2LRDJH
[1 used]
MB 2 Left Rear Door Jamb Hinged $23.42 Order
  SB6-4-RIVET
[15 used]
RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075. $0.05 Order
Ship Modules Separate Ship Modules Separate Option for Modular Units $63.26 Order
MB2-TOPRN Top Return Option for Size 2 Mixing Box - No Filter Option Available. Use top return lid and standard DF base. $379.53 Order
  D2BOTTH
[1 used]
DF 2 Bottom Hinged $118.83 Order
  D2LIDDPRLUP
[1 used]
DF 2 LID Top Return w/Integrated Drip Rail $129.03 Order
  D2LIDDPRL
[-1 used]
DF 2 LID w/Integrated Drip Rail $129.03 Order
  MB2BOTTH
[-1 used]
MB 2 Bottom Hinged $87.16 Order
FIRESTAT-DISCHARGE- Discharge Firestat. Set to 240°F $0.00 Order
FIRESTAT-DISCHARGE Discharge Firestat for Heaters Set to 240°F - Old Controls $308.88 Order
  L4029E1045
[1 used]
DISCHARGE FIRE STAT - High Temperature Limit Switch manual reset, breaks at 240 degrees $129.59 Order
FREEZESTAT Freezestat $0.00 Order
FIRESTAT-INTAKE Intake Firestat for Heaters Set to 135°F - Old Controls $308.88 Order
  L4029E1011
[1 used]
INTAKE FIRE STAT - High Temperature Limit Switch used manual reset, breaks at 135 degrees $96.87 Order
MODULAR-FIRESTAT-INTAKE- Modular Unit Intake Firestat. Set to 135°F. $0.00 Order
  A/CP-DO-240-QC-M
[1 used]
10K, Type II thermistor with 4" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC) $45.32 Order
IBT/RTU remote Space Sensor Remote Room Sensor Option. Wall Mountable 10k Room Sensor and Wire Included. $31.63 Order
  18-8 Plenum Wire
[50 used]
18/8 Plenum rated Thermostat wire. 18 Gauge, 8 conductor. Type CMP/CL2P with PVC Insulation jacket. Meets Article 800. Conductor Colors = Black, Red, White, Green, Brown, Blue, Orange, Yellow. Sold by the foot. 250 foot max continuous run. 75°C (167°F) (A0017722) $2.68 Order
  A/CP-R2
[1 used]
Room Temperature sensor. Thermistor. Wall mount Enclosure. Used with EMSplus & Smart Controls. 10k. $21.83 Order
IBT/RTU remote Space Sensor Temp/Hum Remote Room Sensor Option. Wall Mountable 10k Temp and Humidity Room Sensor Included. $189.68 Order
  A/RH3-CP-R2
[1 used]
Humidity and Temperature Sensor. Wall mounted white plastic cover. For use with single gang junction box. 0-10V humidity reference, 10k thermistor. Requires 18/5 wire back to monitoring panel. $197.36 Order
PRE-PT Pre purge (set at 30 seconds) allowing the blower to purge the inside of the heater. $84.25 Order
CCUTP2 Upturn Plenum for Size 2 Cooling Coil Module - Required for Up Discharge Cooling Coil Applications $416.77 Order
  33008
[2 used]
A0003208 - 3/8" WASHERS $0.14 Order
  P2BACK
[1 used]
DP 2 BACK $94.91 Order
  P2FRNT
[1 used]
DP 2 FRONT $94.91 Order
  P2MNRL
[2 used]
DP 2 MAIN RAIL $25.13 Order
  P2SIDE
[2 used]
DP 2 SIDE $51.63 Order
  17916
[12 used]
GASKETING - Weather Stripping w/PSA , Color Gray, 1/4" X 1" (Price per foot) (17916) $1.09 Order
  INSULATION/sq ft
[39 used]
INSULATION (Price per Sq Foot) $3.98 Order
  MLIFTL
[2 used]
LIFTING LUG $1.88 Order
  SB6-4-RIVET
[50 used]
RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075. $0.05 Order
  P2UBOTT
[1 used]
UP 2 BOTTOM $60.03 Order
  P2ULIDD
[1 used]
UP 2 LID $40.83 Order
VBI-CSF "Insulation" for V-bank Intake Option. $263.28 Order
VB-DS-MB2 V-bank Downstream of Mixing-Box Option Size 2 $1,550.24 Order
DCVWP-SUPPLY Separate 120VAC Wiring Package for Make-Up Air Units. Option must be selected when mounting VFD in prewire panel or with DCV package. Provides separate 120VAC input to supply fan. This 120V signal must be run by electrician from DCV to mua switch. $140.42 Order
VAV-WP-VDC-INPUT-MUA VAV (Variable-Air-Volume) Wiring Package for Commercial Fans. 0-10VDC Speed Control Variable Frequency Drive Included $70.19 Order
VAV-WP-BSPC VAV (Variable-Air-Volume) Wiring Package for Commercial Fans. Building Static Pressure Variable Frequency Drive Control Included $950.09 Order
  A3300-0-LT
[1 used]
Photohelic pressure differential guage (gauge only, accessories listed below), dual relay, pressure range of -.25" w.c. to .25" w.c. low temperature version, standard 80/20 guage. "RPPHOTOHELIC" includes remote mounting box. "A-306" contains pressure kit. $1,182.75 Order
  A-306
[1 used]
Static Pressure Kit for Photohelic, contains 1/8" id tubing, fittings and outdoor sensor. $136.43 Order
VAV-WP-BSPC-PCBMUA VAV (Variable-Air-Volume) Wiring Package for Commercial Fans. Building Static Pressure Variable Frequency Drive Control Included-MUA Board $842.45 Order
  8164
[100 used]
1/4" Nylon Tubing - Used with the Modular Make-Up Air Units A1-D, A2-D, A3-D, A4-D, A5-D and the NHMUA1, NHMUA2, NHMUA3, AI (Price Per Foot). Type 12. $1.17 Order
  69918
[1 used]
3/16" Hose Barb , 1/8" NPT BRASS HOSE BARB FITTING $3.61 Order
  A/MLP2-D25-W-B-A-C-0P
[1 used]
ACI- MLP2 Series Low Differential Pressure transmitters, pressure range of - .25" w.c. to + .25" w.c. low temperature version. Sensor has brass fittings. Accepts 0.25 O.D. x 0.17 I.D. Push On. $177.27 Order
  440097-131280
[1 used]
Female 90 Degree Brass Elbow, Pipe/Thread Size 1/8" $7.70 Order
  90108A417
[2 used]
Zinc Plated Steel Type A USS WASHER, 3/8" Screw Size 1" OD, 0.06"-0.11" Thick $0.22 Order
VAV-WP-DSPC-PCBMUA VAV (Variable-Air-Volume) Wiring Package for Commercial Fans. Duct Static Pressure Variable Frequency Drive Control Included- MUA Board $842.45 Order
  8164
[100 used]
1/4" Nylon Tubing - Used with the Modular Make-Up Air Units A1-D, A2-D, A3-D, A4-D, A5-D and the NHMUA1, NHMUA2, NHMUA3, AI (Price Per Foot). Type 12. $1.17 Order
  69918
[1 used]
3/16" Hose Barb , 1/8" NPT BRASS HOSE BARB FITTING $3.61 Order
  A/MLP2-015-W-B-A-C-0P
[1 used]
ACI- MLP2 Series Low Differential Pressure transmitters, pressure range of - 15" w.c. to + 15" w.c. low temperature version. Sensor has brass fittings. Accepts 0.25 O.D. x 0.17 I.D. Push On. $177.27 Order
  17045A
[1 used]
Airflow Switch Components Cleveland Controls Airflow Probe 4". $7.18 Order
  440097-131280
[1 used]
Female 90 Degree Brass Elbow, Pipe/Thread Size 1/8" $7.70 Order
  90108A417
[2 used]
Zinc Plated Steel Type A USS WASHER, 3/8" Screw Size 1" OD, 0.06"-0.11" Thick $0.22 Order
VAV-WP-MC VAV (Variable-Air-Volume) Wiring Package for Commercial Fans. Manual Speed Control Variable Frequency Drive Included $70.19 Order
VAV-WP-MC-MUA VAV (Variable-Air-Volume) Wiring Package for Commercial Fans. Manual Speed Control Variable Frequency Drive Included $70.19 Order
VAV-WP-PS VAV (Variable-Air-Volume) Wiring Package for Commercial Fans with Frequency Drive. Preset Speed or Speed Reference Variable Frequency Drive Input Field Wired $70.19 Order
VFDINUNIT VFD factory mounted and wired in unit control vestibule. $0.00 Order
Ventilation Direct is committed to customer service and on time, accurate delivery of superior Ventilation products.

Call 1.866.433.8335 for a friendly customer service representative that can customize your exhaust fan, heater or supply air package while providing you a fast quotation including drawings and submittal packages. Our product line includes UL and ANSI listed commercial and industrial exhaust fans, heaters, make-up air units, motors and more with a two year warranty.